Seite 2 von 3

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:48
von maleboya
wurden so vom ART erstellt läuft seiher ohen änderungen

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:50
von maleboya
aber so nebenbei, die 7000 ist auch wählerrisch was die sticks angeht. da hatte ich auch 2 die nicht wollten.

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:52
von BPanther
Die Atevios sind im allgemeinen noch zickiger als die UFS910 habe ich gemerkt. :roll:

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:54
von icwiener
Sodelle.
Ich hab jetzt den Stick mit ext2 formatiert. Leider mit dem selben Ergebnis. Die Kiste bleibt bei "Booting" stehen.

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:54
von maleboya
aber nur bei MINI ... als SWAP frisst meien alles.

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:58
von BPanther
Mach mal nen Log vom hängenbleiben. Dann: HDD eingebaut? Wenn ja -> Bootargs anpassen.

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 20:59
von icwiener
Muss die Partition denn Mini heißen? Meine heißt Neutrino.
Ich habe es jetzt mit und ohne HDD versucht. Immer das gleiche Ergebnis

Wie mach ich ein Log?

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 21:02
von BPanther
Wie gesagt, alles wie bei der 910. Seriell via Putty bekommste das Log...

Bis auf SWAP sind die Namen der Partitionen egal.

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 21:05
von icwiener
Hier das Log. Weiter gehts leider nicht :-(

Code: Alles auswählen

Board: STb7200-HDBOX  [29-bit mode]


U-Boot 1.3.1 (Apr 28 2010 - 15:01:04) - stm23-0032
---created by TDT for general purpose---

DRAM:  128 MB
Flash:   32 MB
In:    serial
Out:   serial
Err:   serial
Frontpanel got PowerOn reset...
init Frontpanel... done, AV7000
Hit any key to stop autoboot:  0
bootmenu_timeout:2000,default:2
add entry:0 - ---flash---
add entry:1 - ---USB1---
add entry:2 - ---USB2---
add entry:3 - ---USB3---
add entry:4 - ---USB4---
add entry:5 - empty
add entry:6 - empty
add entry:7 - empty
add entry:8 - empty
add entry:9 - ---e2-flash---
entering bootmenu - default:2 - ---USB2---
USB:   scanning bus for devices... 3 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found
loading from usb 0:2

1630576 bytes read
## Booting image at a5000000 ...
   Image Name:   Linux-2.6.32.28_stm24_0207
   Image Type:   SuperH Linux Kernel Image (gzip compressed)
   Data Size:    1630512 Bytes =  1.6 MB
   Load Address: 84001000
   Entry Point:  84002000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK

Starting kernel console=ttyAS1,115200 root=/dev/sda2 rw mem=128m ip=192.168.178.250:192.168.1.149:192.168.178.1:255.255.255.0:at7000:eth0:off coprocessor_mem=4m@0x10000000,4m@0x10400000 rootdelay=5 nwhwconf=device:eth0,hwaddr:00:1E:B8:00:A9:A4 init=/bin/devinit - 0x00000000 - 0 ...




Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 21:32
von DboxOldie
Hmm, der Kernel wird geladen, nur bleibt der irgendwo hängen....
Interne HDD hast Du nicht dran ? dann sollte root=/dev/sda2 auch richtig sein.
Da ja Maleboya die gleichen Bootargs hat, würde ich jetzt mal einen anderen Stick versuchen, oder brutal rootdelay=10 probieren.
( Weis jetzt nur nicht wie man das bei der Box setzen kann ) :oops:

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 22:11
von icwiener
Oh man.
Ich dreh durch. Ich habe jetzt zwei andere Sticks versucht. Dort steht nun im Log: Bad Magic Number

Was heißt denn das nun wieder?

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 22:14
von Cent
Das kommt vor wenn die Partitionen zu "groß" sind ...
Mach die mal auf max 512 MB

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 22:29
von DboxOldie
Ja das "Bad Magic..." kommt von U-Boot, wenn er die Partition nicht lesen kann.
Ich formatier dann im Telnet mit der Box so: mkfs.ext2 -m0 -r0 -L MINI1 /dev/sda2 ( für Partition 2 ist klar )
Geht natürlich nur wenn der Stick nicht gemountet ist, dann vorher : umount /dev/sda2

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 22:35
von icwiener
Ojeh!

Ich glaube es liegt am Image! Ich habe es die ganze Zeit mit folgendem Image versucht: BPantherImage[BA-USB]-rev3261-p191.tar.gz

Dacht ich mir nimmst mal dieses: BPantherImage[BA-USB]-rev3261-p179.tar.gz - und damit gehts!!! Eben nochmal mit dem anderen Image versucht -> keine Chance.

Grüßle

Re: Installationsanleitung. Wo?

Verfasst: Mi 7. Mär 2012, 22:44
von BPanther
Wobei aber "Bad Magic" meist auf ein Problem mit dem Stick hinweist.