Installationsprobleme mit BA
Verfasst: Sa 22. Feb 2020, 13:24
Hallo liebe Leute,
da ich auf Unicable umgestiegen bin habe ich auch meine Kathi reaktiviert.
Das bisher verwendete BPanther-Image hat aber mit Unicable nicht funktioniert.
Somit wollte ich diese Version installieren: ufs910_rev18476-ddt.tar.gz
Beim Booten bleibt mit die Kathi damit jedoch stehen.
Das Originale im Flash läuft, mit der Ausnahme, daß ein Kanalsuchlauf immer bei RTL2 abbricht.
Optisch habe ich keine schadhaften Elkos ermitteln können.
Hier der Log über COM1:
__________ Log ___________
NET: Registered protocol family 1
NET: Registered protocol family 17
SMSC: -->Smsc911x_open(dev=0x847074D0)
SMSC: -->Lan_Initialize(dwIntCfg=0x00000011)
SMSC: <--g_GpioSetting set
SMSC: <--Lan_Initialize
SMSC: Testing ISR using IRQ 2
SMSC: ISR passed test using IRQ 2
SMSC: Mac Address is set by parameter to 0x3412FFFD5000
SMSC: -->Phy_Initialize
SMSC: dwPhyId==0x00C0001C,bPhyModel==0x0D,bPhyRev==0x01
SMSC: Successfully Verified Loop Back Packet
SMSC: Passed Loop Back Test
SMSC: <--Phy_Initialize, result=TRUE
SMSC: Tx will use PIO
SMSC: Rx will use PIO
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: <--Smsc911x_open, result=0
SMSC_WARNING: Gpt_CancelCallBack: Failed
IP-Config: Incomplete network configuration information.
SMSC: -->Smsc911x_stop(dev=0x847074D0)
SMSC: <--Smsc911x_stop, result=0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst
ab
: Success
mount: Mounting / on (null) failed: Success
[FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea
d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...[ OK ]
Bringing up the loopback interface...[ OK ]
Setting up hostname...(none)
[ OK ]
BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/config/start.sh exists .... running /config/start.sh
Vendor: SAMSUNG Model: HM320JI Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
ext3: No journal on filesystem on sda1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
device probe found 2 display pipelines
stmfb: fb0 parameters = "1280x720-24@60:3M:NTSC:YUV:YUV"
stmfb: fb1 parameters = "720x576-24@50i:1M:PAL:CVBS"
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
PARAM : boot_param_version=22
PARAM : board=stb7100ref_27
PARAM : bootdelay=1
PARAM : ethaddr=00:50:fd:ff:12:34
PARAM : bootargs=console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2
984 coprocessor_mem=2m@0x04000000,2m@0x04200000
PARAM : autoload=n
PARAM : bootcmd=run baboot; bootm a0040000
PARAM : baboot=if itest.s $baflag == 1; then set baflag 0; saveenv; run baargs;
run bacmd; fi
PARAM : baargs=set bootargs console=ttyAS0,115200 root=$badevice rw ip=$ipaddr:$
serverip:$gateway:255.255.255.0:kathrein:eth0:off mem=64m coprocessor_mem=4m@0x1
0000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin
/devinit
PARAM : bacmd=usb reset;usb reset;ext2load usb $badevid a5000000 boot/uImage;boo
tm a5000000
PARAM : ipaddr=192.168.XXX.XXX
PARAM : serverip=192.168.XXX.XXX
PARAM : gateway=192.168.XXX.XXX
PARAM : badevice=/dev/sda2
PARAM : badevid=0:2
PARAM : stdin=serial
PARAM : stdout=serial
PARAM : stderr=serial
PARAM : baflag=0
BOOT PARAM VERSION = 22
UFS-910 found
mknod: /dev/vfd: File exists
vfd_driver_new: module license 'Marusys' taints kernel.
tmp_pin = 8477dcc8
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
UFS910 Button Device Driver(by Marusys Co.)
SysConf device Init
LMI_SYS VCR0 = 00d40000
LMI_SYS VCR1 = 0f041000
LMI_SYS MIM0 = 861a0247
LMI_SYS MIM1 = 01010022
LMI_SYS SCR = 00000000
LMI_SYS STR = 35b06455
LMI_SYS COC = 00000000
LMI_SYS SDRA0 = 08001900
LMI_SYS SDRA1 = 08001900
LMI_SYS CIC = 00000249
LMI_SYS SDMR0 = 00000000
LMI_SYS SDMR1 = 00000000
LMI_VID VCR0 = 00d40000
LMI_VID VCR1 = 17101000
LMI_VID MIM0 = 861a0247
LMI_VID MIM1 = 01010022
LMI_VID SCR = 00000000
LMI_VID STR = 35b06455
LMI_VID COC = 00000000
LMI_VID SDRA0 = 14001900
LMI_VID SDRA1 = 14001900
LMI_VID CIC = 00000249
LMI_VID SDMR0 = 00000000
LMI_VID SDMR1 = 00000000
VFD_Driver Init
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
TestModMgr::CheckTestMode CmdLine = console=ttyAS0,115200 root=/dev/mtdblock3 me
m=41m bigphysarea=2984 coprocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2984 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2984 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
cannot fine test mode
TestModeMgr::CheckMode : TestMode Disabled
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 400
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
## Error: "ba2cmd" not defined
## Booting image at a0040000 ...
Image Name: Linux-2.6.17.14_stm22_0037
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1783856 Bytes = 1.7 MB
Load Address: 84401000
Entry Point: 84402000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=29
84 coprocessor_mem=2m@0x04000000,2m@0x04200000 - 0x00000000 - 0 ...
Linux version 2.6.17.14_stm22_0037 (rarr@KnopBox) (gcc-Version 4.1.1 (STMicroele
ctronics/Linux Base 4.1.1-23)) #1 PREEMPT Wed Jul 16 12:06:17 CEST 2008
STMicroelectronics STb7100 Reference board initialisation
STb7100 version 3.x
Built 1 zonelists
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysar
ea=2984 coprocessor_mem=2m@0x04000000,2m@0x04200000
st-coprocessor: Failed to reserve memory at 0x04000000
st-coprocessor: Failed to reserve memory at 0x04200000
PID hash table entries: 256 (order: 8, 1024 bytes)
Using tmu for system timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 26000k/41984k available (2985k kernel code, 15964k reserved, 368k data,
96k init)
PVR=04061100 CVR=30480000 PRR=00009100
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STb710x
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
bigphysarea: Allocated 2984 pages at 0x847e3000.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Device probe found data for platform device lirc
lirc_dev: IR Remote Control driver registered, at major 61
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_dev: lirc_register_plugin: plugin lirc_stm owner 00000000
STM LIRC plugin has IRQ 125
Lirc STM: Using IRB mode
STMicroelectronics LIRC driver configured
STPIO layer initialised
VFD_Controller Type : NEW Kathrein VFD
STMicroelectronics ASC driver initialized
ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
s_env_mac[0] = 0
s_env_mac[1] = 0
s_env_mac[2] = :
s_env_mac[3] = 5
s_env_mac[4] = 0
s_env_mac[5] = :
s_env_mac[6] = f
s_env_mac[7] = d
s_env_mac[8] = :
s_env_mac[9] = f
s_env_mac[10] = f
s_env_mac[11] = :
s_env_mac[12] = 1
s_env_mac[13] = 2
s_env_mac[14] = :
s_env_mac[15] = 3
s_env_mac[16] = 4
get ether addr = 0, 50, fd, ff, 12, 34
mac hi address = 3412, lowaddress = fffd5000
SMSC: --> init_module()
SMSC: Driver Version = 1.21
SMSC: Compiled: Jul 16 2008, 12:05:15
SMSC: Platform: ST40 STMICRO r3
SMSC: Driver Parameters
SMSC: lan_base = 0x00000000, driver will decide
SMSC: bus_width = 0, driver will autodetect
SMSC: link_mode = 0x7F, 10HD,10FD,100HD,100FD,ASYMP,SYMP,ANEG
SMSC: irq = 2
SMSC: int_deas = 0xFFFFFFFF, use platform default
SMSC: irq_pol = 1, IRQ output is active high
SMSC: irq_type = 1, IRQ output is Push-Pull driver
SMSC: rx_dma = 256, RX will use PIO
SMSC: tx_dma = 256, TX will use PIO
SMSC: dma_threshold = 200
SMSC: mac_addr_hi16 = 0x00003412
SMSC: mac_addr_lo32 = 0xFFFD5000
SMSC: debug_mode = 0x00000007
SMSC: tx_fif_sz = 0x00050000
SMSC: afc_cfg = 0xFFFFFFFF, driver will decide
SMSC: tasklets = 0, Tasklets disabled
SMSC: phy_addr = 0xFFFFFFFF, Use internal phy
SMSC: max_throughput = 0xFFFFFFFF, Use platform default
SMSC: max_packet_count = 0xFFFFFFFF, Use platform default
SMSC: packet_cost = 0xFFFFFFFF, Use platform default
SMSC: burst_period = 0xFFFFFFFF, Use platform default
SMSC: max_work_load = 0xFFFFFFFF, Use platform default
SMSC: -->Smsc911x_init(dev=0x847074D0)
SMSC: --> Platform_Initialize
SMSC: Lan Base at 0xA2000000
SMSC: <-- Platform_Initialize
SMSC: dwLanBase=0xA2000000
SMSC: LAN9115 identified, dwIdRev==0x01150001
SMSC: FPGA_REV == 0x00000000
SMSC: <--Smsc911x_init(), result=0
SMSC: Interface Name = "eth0"
SMSC: <-- init_module()
nwhw_config: device not found
ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170
ata1: SATA link down (SStatus 0)
scsi0 : sata_stm
Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Onboard_Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 2
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 11 MTD partitions on "Onboard_Flash":
0x00000000-0x00020000 : "Boot firmware : 0xA000.0000-0xA001.FFFF"
0x00040000-0x00200000 : "Kernel - 0xA004.0000-0xA01F.FFFF"
0x00200000-0x002a0000 : "Config FS - 0xA020.0000-0xA029.FFFF"
0x002a0000-0x004e0000 : "Root SQUASHFS- 0xA02A.0000-0xA04D.FFFF"
0x004e0000-0x00ae0000 : "APP_Modules 0xA04E.0000-0xA0AD.FFFF"
0x00ae0000-0x00c00000 : "EmergencyRoot 0xA0AE.0000-0xA0BF.FFFF"
0x00c00000-0x00fc0000 : "OtherData Var 0xA0C0.0000-0xA0FB.FFFF"
0x00020000-0x00040000 : "BootConfiguration 0xA002.0000-0xA003.FFFF"
0x00fc0000-0x00fd0000 : "2nd BootConfiguration 0xA0FC.0000-0xA0FC.FFFF"
0x00fd0000-0x01000000 : "2nd Boot firmware : 0xA0FD.0000-0xA0FF.FFFF"
0x00040000-0x01000000 : "Flash wo/ Bootloader 0xA004.0000-0xA0FF.FFFF"
ST40_start_host_control
ST40_start_host_control proceeding
ST40-ehci ST40-ehci.2: ST EHCI Host Controller
ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1
ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00
ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: ST EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17.14_stm22_0037 ehci_hcd
usb usb1: SerialNumber: STB7100_EHCI
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ST40-ehci and address 2
usb 1-1: Product: USB2.0 Hub
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.3: new high speed USB device using ST40-ehci and address 3
usb 1-1.3: Product: Portable USB Drive
usb 1-1.3: Manufacturer: Verbatim
usb 1-1.3: SerialNumber: 6830000168d1
usb 1-1.3: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver libusual
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
stssc layer initialized
STMicroelectronics - Coprocessors st231 Init
st231-0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4000000 size 0x00200000
cop. addr 0x04000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231-1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4200000 size 0x00200000
cop. addr 0x04200000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
TCP bic registered
TCP highspeed registered
NET: Registered protocol family 1
NET: Registered protocol family 17
SMSC: -->Smsc911x_open(dev=0x847074D0)
SMSC: -->Lan_Initialize(dwIntCfg=0x00000011)
SMSC: <--g_GpioSetting set
SMSC: <--Lan_Initialize
SMSC: Testing ISR using IRQ 2
SMSC: ISR passed test using IRQ 2
SMSC: Mac Address is set by parameter to 0x3412FFFD5000
SMSC: -->Phy_Initialize
SMSC: dwPhyId==0x00C0001C,bPhyModel==0x0D,bPhyRev==0x01
SMSC: Successfully Verified Loop Back Packet
SMSC: Passed Loop Back Test
SMSC: <--Phy_Initialize, result=TRUE
SMSC: Tx will use PIO
SMSC: Rx will use PIO
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: <--Smsc911x_open, result=0
SMSC_WARNING: Gpt_CancelCallBack: Failed
IP-Config: Incomplete network configuration information.
SMSC: -->Smsc911x_stop(dev=0x847074D0)
SMSC: <--Smsc911x_stop, result=0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst
ab
: Success
mount: Mounting / on (null) failed: Success
[FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea
d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...[ OK ]
Bringing up the loopback interface...[ OK ]
Setting up hostname...(none)
[ OK ]
BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/config/start.sh exists .... running /config/start.sh
Vendor: SAMSUNG Model: HM320JI Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
ext3: No journal on filesystem on sda1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
device probe found 2 display pipelines
stmfb: fb0 parameters = "1280x720-24@60:3M:NTSC:YUV:YUV"
stmfb: fb1 parameters = "720x576-24@50i:1M:PAL:CVBS"
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
Restar
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 400
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
Saving Environment to Flash...
env buffer crc = 535b65fa, data = 85e0000c
..
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash... .done
..
Protected 2 sectors
## Starting application at 0xA0FD0000 ...
Board: STb7100 Marusys MSS-5000 Custom [29-bit mode]
U-Boot 1.3.1 (Jul 1 2008 - 20:43:53) - stm23_0032
DRAM: 64 MB
Flash: 16 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... .done
. done
Protected 1 sectors
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
1633337 bytes read
## Booting image at a5000000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1633273 Bytes = 1.6 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/sda2 rw ip=192.168.XXX.XXX:192.16
8.XXX.XXX:192.168.XXX.XXX:255.255.255.0:kathrein:eth0:off mem=64m coprocessor_mem=
4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:1d:ec:00:
00:00 init=/bin/devinit - 0x00000000 - 0 ...
__________ Log ___________
Für Hilfe dankbar
Michi
da ich auf Unicable umgestiegen bin habe ich auch meine Kathi reaktiviert.
Das bisher verwendete BPanther-Image hat aber mit Unicable nicht funktioniert.
Somit wollte ich diese Version installieren: ufs910_rev18476-ddt.tar.gz
Beim Booten bleibt mit die Kathi damit jedoch stehen.
Das Originale im Flash läuft, mit der Ausnahme, daß ein Kanalsuchlauf immer bei RTL2 abbricht.
Optisch habe ich keine schadhaften Elkos ermitteln können.
Hier der Log über COM1:
__________ Log ___________
NET: Registered protocol family 1
NET: Registered protocol family 17
SMSC: -->Smsc911x_open(dev=0x847074D0)
SMSC: -->Lan_Initialize(dwIntCfg=0x00000011)
SMSC: <--g_GpioSetting set
SMSC: <--Lan_Initialize
SMSC: Testing ISR using IRQ 2
SMSC: ISR passed test using IRQ 2
SMSC: Mac Address is set by parameter to 0x3412FFFD5000
SMSC: -->Phy_Initialize
SMSC: dwPhyId==0x00C0001C,bPhyModel==0x0D,bPhyRev==0x01
SMSC: Successfully Verified Loop Back Packet
SMSC: Passed Loop Back Test
SMSC: <--Phy_Initialize, result=TRUE
SMSC: Tx will use PIO
SMSC: Rx will use PIO
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: <--Smsc911x_open, result=0
SMSC_WARNING: Gpt_CancelCallBack: Failed
IP-Config: Incomplete network configuration information.
SMSC: -->Smsc911x_stop(dev=0x847074D0)
SMSC: <--Smsc911x_stop, result=0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst
ab
: Success
mount: Mounting / on (null) failed: Success
[FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea
d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...[ OK ]
Bringing up the loopback interface...[ OK ]
Setting up hostname...(none)
[ OK ]
BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/config/start.sh exists .... running /config/start.sh
Vendor: SAMSUNG Model: HM320JI Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
ext3: No journal on filesystem on sda1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
device probe found 2 display pipelines
stmfb: fb0 parameters = "1280x720-24@60:3M:NTSC:YUV:YUV"
stmfb: fb1 parameters = "720x576-24@50i:1M:PAL:CVBS"
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
PARAM : boot_param_version=22
PARAM : board=stb7100ref_27
PARAM : bootdelay=1
PARAM : ethaddr=00:50:fd:ff:12:34
PARAM : bootargs=console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2
984 coprocessor_mem=2m@0x04000000,2m@0x04200000
PARAM : autoload=n
PARAM : bootcmd=run baboot; bootm a0040000
PARAM : baboot=if itest.s $baflag == 1; then set baflag 0; saveenv; run baargs;
run bacmd; fi
PARAM : baargs=set bootargs console=ttyAS0,115200 root=$badevice rw ip=$ipaddr:$
serverip:$gateway:255.255.255.0:kathrein:eth0:off mem=64m coprocessor_mem=4m@0x1
0000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:$ethaddr init=/bin
/devinit
PARAM : bacmd=usb reset;usb reset;ext2load usb $badevid a5000000 boot/uImage;boo
tm a5000000
PARAM : ipaddr=192.168.XXX.XXX
PARAM : serverip=192.168.XXX.XXX
PARAM : gateway=192.168.XXX.XXX
PARAM : badevice=/dev/sda2
PARAM : badevid=0:2
PARAM : stdin=serial
PARAM : stdout=serial
PARAM : stderr=serial
PARAM : baflag=0
BOOT PARAM VERSION = 22
UFS-910 found
mknod: /dev/vfd: File exists
vfd_driver_new: module license 'Marusys' taints kernel.
tmp_pin = 8477dcc8
VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
UFS910 Button Device Driver(by Marusys Co.)
SysConf device Init
LMI_SYS VCR0 = 00d40000
LMI_SYS VCR1 = 0f041000
LMI_SYS MIM0 = 861a0247
LMI_SYS MIM1 = 01010022
LMI_SYS SCR = 00000000
LMI_SYS STR = 35b06455
LMI_SYS COC = 00000000
LMI_SYS SDRA0 = 08001900
LMI_SYS SDRA1 = 08001900
LMI_SYS CIC = 00000249
LMI_SYS SDMR0 = 00000000
LMI_SYS SDMR1 = 00000000
LMI_VID VCR0 = 00d40000
LMI_VID VCR1 = 17101000
LMI_VID MIM0 = 861a0247
LMI_VID MIM1 = 01010022
LMI_VID SCR = 00000000
LMI_VID STR = 35b06455
LMI_VID COC = 00000000
LMI_VID SDRA0 = 14001900
LMI_VID SDRA1 = 14001900
LMI_VID CIC = 00000249
LMI_VID SDMR0 = 00000000
LMI_VID SDMR1 = 00000000
VFD_Driver Init
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
TestModMgr::CheckTestMode CmdLine = console=ttyAS0,115200 root=/dev/mtdblock3 me
m=41m bigphysarea=2984 coprocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2984 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
CMDLINE = console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=2984 cop
rocessor_mem=2m@0x04000000,2m@0x04200000
cannot fine test mode
TestModeMgr::CheckMode : TestMode Disabled
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 400
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
## Error: "ba2cmd" not defined
## Booting image at a0040000 ...
Image Name: Linux-2.6.17.14_stm22_0037
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1783856 Bytes = 1.7 MB
Load Address: 84401000
Entry Point: 84402000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysarea=29
84 coprocessor_mem=2m@0x04000000,2m@0x04200000 - 0x00000000 - 0 ...
Linux version 2.6.17.14_stm22_0037 (rarr@KnopBox) (gcc-Version 4.1.1 (STMicroele
ctronics/Linux Base 4.1.1-23)) #1 PREEMPT Wed Jul 16 12:06:17 CEST 2008
STMicroelectronics STb7100 Reference board initialisation
STb7100 version 3.x
Built 1 zonelists
Kernel command line: console=ttyAS0,115200 root=/dev/mtdblock3 mem=41m bigphysar
ea=2984 coprocessor_mem=2m@0x04000000,2m@0x04200000
st-coprocessor: Failed to reserve memory at 0x04000000
st-coprocessor: Failed to reserve memory at 0x04200000
PID hash table entries: 256 (order: 8, 1024 bytes)
Using tmu for system timer
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 26000k/41984k available (2985k kernel code, 15964k reserved, 368k data,
96k init)
PVR=04061100 CVR=30480000 PRR=00009100
I-cache : n_ways=2 n_sets=256 way_incr=8192
I-cache : entry_mask=0x00001fe0 alias_mask=0x00001000 n_aliases=2
D-cache : n_ways=2 n_sets=512 way_incr=16384
D-cache : entry_mask=0x00003fe0 alias_mask=0x00003000 n_aliases=4
Mount-cache hash table entries: 512
CPU: STb710x
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
bigphysarea: Allocated 2984 pages at 0x847e3000.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Device probe found data for platform device lirc
lirc_dev: IR Remote Control driver registered, at major 61
lirc_dev: lirc_register_plugin: sample_rate: 0
lirc_dev: lirc_register_plugin: plugin lirc_stm owner 00000000
STM LIRC plugin has IRQ 125
Lirc STM: Using IRB mode
STMicroelectronics LIRC driver configured
STPIO layer initialised
VFD_Controller Type : NEW Kathrein VFD
STMicroelectronics ASC driver initialized
ttyAS0 at MMIO 0xb8032000 (irq = 121) is a asc
ttyAS1 at MMIO 0xb8033000 (irq = 120) is a asc
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
s_env_mac[0] = 0
s_env_mac[1] = 0
s_env_mac[2] = :
s_env_mac[3] = 5
s_env_mac[4] = 0
s_env_mac[5] = :
s_env_mac[6] = f
s_env_mac[7] = d
s_env_mac[8] = :
s_env_mac[9] = f
s_env_mac[10] = f
s_env_mac[11] = :
s_env_mac[12] = 1
s_env_mac[13] = 2
s_env_mac[14] = :
s_env_mac[15] = 3
s_env_mac[16] = 4
get ether addr = 0, 50, fd, ff, 12, 34
mac hi address = 3412, lowaddress = fffd5000
SMSC: --> init_module()
SMSC: Driver Version = 1.21
SMSC: Compiled: Jul 16 2008, 12:05:15
SMSC: Platform: ST40 STMICRO r3
SMSC: Driver Parameters
SMSC: lan_base = 0x00000000, driver will decide
SMSC: bus_width = 0, driver will autodetect
SMSC: link_mode = 0x7F, 10HD,10FD,100HD,100FD,ASYMP,SYMP,ANEG
SMSC: irq = 2
SMSC: int_deas = 0xFFFFFFFF, use platform default
SMSC: irq_pol = 1, IRQ output is active high
SMSC: irq_type = 1, IRQ output is Push-Pull driver
SMSC: rx_dma = 256, RX will use PIO
SMSC: tx_dma = 256, TX will use PIO
SMSC: dma_threshold = 200
SMSC: mac_addr_hi16 = 0x00003412
SMSC: mac_addr_lo32 = 0xFFFD5000
SMSC: debug_mode = 0x00000007
SMSC: tx_fif_sz = 0x00050000
SMSC: afc_cfg = 0xFFFFFFFF, driver will decide
SMSC: tasklets = 0, Tasklets disabled
SMSC: phy_addr = 0xFFFFFFFF, Use internal phy
SMSC: max_throughput = 0xFFFFFFFF, Use platform default
SMSC: max_packet_count = 0xFFFFFFFF, Use platform default
SMSC: packet_cost = 0xFFFFFFFF, Use platform default
SMSC: burst_period = 0xFFFFFFFF, Use platform default
SMSC: max_work_load = 0xFFFFFFFF, Use platform default
SMSC: -->Smsc911x_init(dev=0x847074D0)
SMSC: --> Platform_Initialize
SMSC: Lan Base at 0xA2000000
SMSC: <-- Platform_Initialize
SMSC: dwLanBase=0xA2000000
SMSC: LAN9115 identified, dwIdRev==0x01150001
SMSC: FPGA_REV == 0x00000000
SMSC: <--Smsc911x_init(), result=0
SMSC: Interface Name = "eth0"
SMSC: <-- init_module()
nwhw_config: device not found
ata1: SATA max UDMA/133 cmd 0xB9209000 ctl 0xB9209820 bmdma 0x0 irq 170
ata1: SATA link down (SStatus 0)
scsi0 : sata_stm
Generic ST boards onboard flash device: 0x01000000 (16.0Mb) at 0x00000000
Onboard_Flash: Found 1 x16 devices at 0x0 in 16-bit bank
Onboard_Flash: Found 1 x16 devices at 0x800000 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Onboard_Flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 2
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 11 MTD partitions on "Onboard_Flash":
0x00000000-0x00020000 : "Boot firmware : 0xA000.0000-0xA001.FFFF"
0x00040000-0x00200000 : "Kernel - 0xA004.0000-0xA01F.FFFF"
0x00200000-0x002a0000 : "Config FS - 0xA020.0000-0xA029.FFFF"
0x002a0000-0x004e0000 : "Root SQUASHFS- 0xA02A.0000-0xA04D.FFFF"
0x004e0000-0x00ae0000 : "APP_Modules 0xA04E.0000-0xA0AD.FFFF"
0x00ae0000-0x00c00000 : "EmergencyRoot 0xA0AE.0000-0xA0BF.FFFF"
0x00c00000-0x00fc0000 : "OtherData Var 0xA0C0.0000-0xA0FB.FFFF"
0x00020000-0x00040000 : "BootConfiguration 0xA002.0000-0xA003.FFFF"
0x00fc0000-0x00fd0000 : "2nd BootConfiguration 0xA0FC.0000-0xA0FC.FFFF"
0x00fd0000-0x01000000 : "2nd Boot firmware : 0xA0FD.0000-0xA0FF.FFFF"
0x00040000-0x01000000 : "Flash wo/ Bootloader 0xA004.0000-0xA0FF.FFFF"
ST40_start_host_control
ST40_start_host_control proceeding
ST40-ehci ST40-ehci.2: ST EHCI Host Controller
ST40-ehci ST40-ehci.2: new USB bus registered, assigned bus number 1
ST40-ehci ST40-ehci.2: irq 169, io mem 0xb91ffe00
ST40-ehci ST40-ehci.2: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: Product: ST EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.17.14_stm22_0037 ehci_hcd
usb usb1: SerialNumber: STB7100_EHCI
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usb 1-1: new high speed USB device using ST40-ehci and address 2
usb 1-1: Product: USB2.0 Hub
usb 1-1: configuration #1 chosen from 1 choice
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 4 ports detected
usb 1-1.3: new high speed USB device using ST40-ehci and address 3
usb 1-1.3: Product: Portable USB Drive
usb 1-1.3: Manufacturer: Verbatim
usb 1-1.3: SerialNumber: 6830000168d1
usb 1-1.3: configuration #1 chosen from 1 choice
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver libusual
pegasus: v0.6.13 (2005/11/13), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new driver pegasus
usbcore: registered new driver asix
usbcore: registered new driver cdc_ether
usbcore: registered new driver net1080
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
stssc layer initialized
STMicroelectronics - Coprocessors st231 Init
st231-0 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4000000 size 0x00200000
cop. addr 0x04000000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
st231-1 Coprocessor -------------------------------------------
flags 0001 RAM start at 0xa4200000 size 0x00200000
cop. addr 0x04200000
Channels : Not defined
IRQ : not used
---------------------------------------------------------------
TCP bic registered
TCP highspeed registered
NET: Registered protocol family 1
NET: Registered protocol family 17
SMSC: -->Smsc911x_open(dev=0x847074D0)
SMSC: -->Lan_Initialize(dwIntCfg=0x00000011)
SMSC: <--g_GpioSetting set
SMSC: <--Lan_Initialize
SMSC: Testing ISR using IRQ 2
SMSC: ISR passed test using IRQ 2
SMSC: Mac Address is set by parameter to 0x3412FFFD5000
SMSC: -->Phy_Initialize
SMSC: dwPhyId==0x00C0001C,bPhyModel==0x0D,bPhyRev==0x01
SMSC: Successfully Verified Loop Back Packet
SMSC: Passed Loop Back Test
SMSC: <--Phy_Initialize, result=TRUE
SMSC: Tx will use PIO
SMSC: Rx will use PIO
SMSC_WARNING: Gpt_CancelCallBack: Failed
SMSC: <--Smsc911x_open, result=0
SMSC_WARNING: Gpt_CancelCallBack: Failed
IP-Config: Incomplete network configuration information.
SMSC: -->Smsc911x_stop(dev=0x847074D0)
SMSC: <--Smsc911x_stop, result=0
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
/etc/init.d/rcS running...
Remounting root file system in read-write mode...mount: Can't find / in /etc/fst
ab
: Success
mount: Mounting / on (null) failed: Success
[FAILED]
/etc/rcS.d/S200mountfs: /etc/rcS.d/S200mountfs: 91: cannot create /etc/mtab: Rea
d-only file system
mount: Can't find / in /etc/fstab
: Success
mount: Mounting / on (null) failed: Success
Mounting other file systems...[ OK ]
Bringing up the loopback interface...[ OK ]
Setting up hostname...(none)
[ OK ]
BusyBox v1.1.0 (2006.03.02-09:48+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
/config/start.sh exists .... running /config/start.sh
Vendor: SAMSUNG Model: HM320JI Rev:
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
SCSI device sda: 625142448 512-byte hdwr sectors (320073 MB)
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
usb 1-1.3: reset high speed USB device using ST40-ehci and address 3
sda: Write Protect is off
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4
sd 1:0:0:0: Attached scsi disk sda
ext3: No journal on filesystem on sda1
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
device probe found 2 display pipelines
stmfb: fb0 parameters = "1280x720-24@60:3M:NTSC:YUV:YUV"
stmfb: fb1 parameters = "720x576-24@50i:1M:PAL:CVBS"
VFD PIO Already Opened
VFD PIO Already Opened
VFD PIO Already Opened
VFD_Controller Type : NEW Kathrein VFD
Restar
Board: STb7100-mboard
U-Boot 1.1.2 (STLINUX_2_0p1) (May 30 2007 - 16:03:49)
DRAM: 32 MB
write time out = 1, clock = 40
write time out = 1, clock = 40
Flash: 16 MB
In: serial
Out: serial
Err: serial
pll0 freq 531
pll1 freq 400
Net: VFD_Driver Init
VFD_Controller Type : NEW Kathrein VFD
board_version = 0
Button_value = 7
Hit any key to stop autoboot: 0
Saving Environment to Flash...
env buffer crc = 535b65fa, data = 85e0000c
..
Un-Protected 2 sectors
Erasing Flash...
.. done
Erased 2 sectors
Writing to Flash... .done
..
Protected 2 sectors
## Starting application at 0xA0FD0000 ...
Board: STb7100 Marusys MSS-5000 Custom [29-bit mode]
U-Boot 1.3.1 (Jul 1 2008 - 20:43:53) - stm23_0032
DRAM: 64 MB
Flash: 16 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
Saving Environment to Flash...
. done
Un-Protected 1 sectors
Erasing Flash...
. done
Erased 1 sectors
Writing to Flash... .done
. done
Protected 1 sectors
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
(Re)start USB...
USB: scanning bus for devices... 3 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
1633337 bytes read
## Booting image at a5000000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1633273 Bytes = 1.6 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel console=ttyAS0,115200 root=/dev/sda2 rw ip=192.168.XXX.XXX:192.16
8.XXX.XXX:192.168.XXX.XXX:255.255.255.0:kathrein:eth0:off mem=64m coprocessor_mem=
4m@0x10000000,4m@0x10400000 rootdelay=6 nwhwconf=device:eth0,hwaddr:00:1d:ec:00:
00:00 init=/bin/devinit - 0x00000000 - 0 ...
__________ Log ___________
Für Hilfe dankbar
Michi