Is it possible to make an image of a neutrino...?

[zozman]

The patch sets only the same values again. You can do this also via telnet.

Code: Alles auswählen

echo A1 > /proc/stb/tsmux/ci0_input
echo A1 > /proc/stb/tsmux/input0
echo A1 > /proc/stb/tsmux/input1

Does this change anything?

[atef 0]

I do not know what to say
But these are all discussions because the tuner does not work on the DM 7080
And DM 920

Untitled.png

[zozman]

Here a short change. But strange, that the dm900 work and the dm920 not same for dm820<->dm7080.

But I think there's an other problem which has nothing to do with the CI control.


EDIT: Attachment removed.

[zozman]

I'm afraid, the user with the problems uses only 1 connection at the tuner, right? This problem I have here also. I MUST use both inputs at the tuner or I have no signal. With Unicable/Jess here no problem...

[atef 0]

I don't know honestly
But the user executed these three commands
Attached from your end and it started scanning the channels without problems
That is, the three commands fix the problem
That's on DM 920
User DM 7080 has not received a response yet

Code: Alles auswählen

echo A1 > /proc/stb/tsmux/ci0_input
echo A1 > /proc/stb/tsmux/input0
echo A1 > /proc/stb/tsmux/input1

[atef 0]

This is more than strage. As I sayed, these are the defaults after box start and already set. The user can try if these 3 command also work if he write them to the file /var/etc/vorneutrino.sh. If this working, then we have a workaround. The attached new binary for the dm920 should do the same.

And an other strange thing with the dual (tripple) tuner: If I deactivate tuner 2 (B) at neutrino I can use only one dat cable BUT at input for tuner 2 (LNB 2). But works only for some transponder. If I want all, I must still use both tuner connections. Very strange tuner...


EDIT: New dm920 version uploaded.

[atef 0]

New experimental images uploaded for dm7080, dm900 and dm920. If installed in flash just update per online update (service menu). Hope the tuner works now right. I have tryed to adapt the e2 patch, but also the 3 lines before neutrino starting used.

[atef 0]

New experimental images uploaded for dm7080, dm900 and dm920. If installed in flash just update per online update (service menu). Hope the tuner works now right. I have tryed to adapt the e2 patch, but also the 3 lines before neutrino starting used.

Unfortunately, even this new version
The channels do not work on it until after the three commands are executed
On both devices DM 920 & 7080

[atef 0]

I know, I have removed the 3 images and build current new one - testet with DM7080.

Also fixed for the DM7080/820/900/920: The serial log with the mini usb connection also now working.

EDIT: DM7080 done and working. Also fixed the online update (if flash installed). Don't use it with older versions.
EDIT2: The DM7080 LCD is working. The default brightness is too low. Adjust e.g. to 150 and all will be displayed.

[atef 0]

Now the DM 7080 works fine
DM 920 user has not responded yet

[atef 0]

Also the DM 920 works well now
Thank you

[atef 0]

May only some small changes needed, but the most functions should now working. That's good.

BTW: The DM7080 LCD has 132x64x8 - the internal lcd driver tells me this.

[DM900]

This tuner not getting signal in second tuner Mean A1 with discqc1.1 only getting signal in A2 with diseqc 1.0

IMG_20240605_184834.jpg

[DM900]

Set tuner 1 to Independent how the tuner 2. Master only if the other a slave (twin/loop).

[DM900]

Set tuner 1 to Independent how the tuner 2. Master only if the other a slave (twin/loop).

I try that also but not working
Tuner A1 with diseqc 1.1 not working no signal in scanning
And tuner A2 with diseqc 1.0 working channels scanning and working