BPanther's Neutrino Forum

jo ist ext4

die hdd ist nicht unter /tmp/mnt zu finden kann ja dann auch nicht

warum wurde ext4 deaktiviert (ging recht gut bei mir)

ext4 wurde wie gesagt abgeschaltet (Kernel wieder kleiner), daher hast Du das Problem. Es ist nur noch ext2/3 enthalten.

danke dann werd ich mal wieder ext3 draus machen

jo mit ext3 geht alles wieder

BIG THX

Hello,
I'm from Estonia and therefore I write here in English.
I do hope that English usage is OK in BPanther's Neutrino Forum.
I have been used several Kathy UFS 910 from their beginning, probably some know my nickname from other UFS 910 forums

Now I started to test latest Neutrino flash image 3924 and it is very nice , almost everything is OK and fast working compared with e2 flash images made by AAF.
BUT...
I have big problem with using of my DiSEqC 1.1 switch, what works without any problem with different e2 images on Kathy 910 and Kathy 922. So switch should be OK, but Neutrino software seems to be not capable to handle this switch.

I have in current use 8 LNB-s, connected to DiSeqC 1.1 switch inputs 1,2,3,4 and 7,8,9,10.
If I used service setting "DiSEqC 1.1" , then no scanning of any those LNB-s.
Then I changed setting to "advanced", and some scanning was now possible but no LNB was connected as intended, but somehow different...
Here is list:
tried to scan LNB connected to
input 4, but scanned was input 2 LNB
input 3......................... input 7
input 2......................... input 10
input 7 ......................... input 10 (again???)

strange that on input 1 was not possible to scan , however it should be direct through connection. In the same time when I changed to "no DiSEqC" then LNB on input 1 was scanned as it should be.
No scan results on input 1, input 8, input 9 (maybe just frequencies to be searched did not match?)

Could it be possible to manage DiSEqC 1.1 switching as it should be?
Then image 3924 would be very nice to use.
I could not test DVB subtitles,as I could not scan Thor 0,8W satellite, connected to switch input 4.
Also I could not receive former Sirius 4,8E, connected to input 3 (see table above)

Waiting for some kind advice,
best regards
Henkka from Estonia

There is no problem with english.
Can you try please the stm22 version to test if this a problem only with the stm24 version?

BPanther-Mobil hat geschrieben:There is no problem with english.
Can you try please the stm22 version to test if this a problem only with the stm24 version?

Yes definitely I will install today evening stm22 version and test it.
Then I will inform about test results.

Additional question:
how should Neutrino flash image be correctly configured in case that I use DiSeqC switch 1/10 (8 inputs are used according to my signature) , protocol DiSEqC 1.1 ?
Configuration possibilities in Neutrino are different compared with any e2 image. This DiSEqC switch works perfectly with any e2 images (both flash and USB) installed on Kathy UFS 910 and UFS 922.

Ich als auch andere haben ja mit den neuen stm24-Revs (ab 37..) Probleme mit "Kanal nicht verfügbar" nach dem Einschalten. Fakt ist, daß mit Einstellung DiSeqC 1.1 statt 1.0 (was richtig wäre bei Astra/Hotbird) dieser Fehler fast nicht mehr auftritt. Mit stm 22 tritt das nicht auf!
Das deutet schon auf einen stm24-Fehler hin. Mich wundert nur, daß das hier so wenige "murren" bzw. kein DiSeqC verwenden.

@henkka: I don't know about your config, here I use a rotor (extended diseqc settings). You should try both if you don't know the protocol of your switch.

@blacky49: Wie gesagt, ich kann ja nur Motor testen und das läuft über die erweiterte Konfig.

Now I have tested stm22 version of the rev3924 and results are pretty good.
For my DiSEqC switch 1/10 there was needed to use "Advanced" DiSEqC setting and then to define LNB input number as "uncommited".
"commited" LNB input number I left to "off".
Scanning of almost all satellites was successful, except 36E satellite, where I use circular polarization LNB for Russian programs reception.
Special local oscillators setup is needed for this LNB, 10750 MHz on every position.
This works perfectly with e2 images but did not work with Neutrino.

Another not so nice surprise for me was DVB subtitling.
Subtitles are located in unusual place in left side middle height of the screen (again, I have been used AAF e2 images since now and there is everything more usual for me, also subtitles are in place more suitable for me).

Third unexpected surprise - Viasat EPG on 4,8E satellite seems not to work. Again - AAF e2 flash image EPG works perfectly on 4,8E Viasat.
But in every other meaning Neutrino gives much more positive impression compared with AAF e2 flash images. It is fast and clear, and no unexpected "green screen", what is unfortunately usual thing when using e2 flash image on Kathy 910...

Please don't get me wrong - I'm just explaining some things about Neutrino what (according to my personal understanding) maybe should be reconsidered and redesigned...

At all - now I need some time to get more familiar with Neutrino flash image for Kathy 910.
But start is pretty nice

And it seems that there is something wrong with stm24 rev.3924 ???

I got a similiar problem - with my UFS922 and stm24

since i reorganized my satellites.xml in the same order as my DiSEqC order - it worked properly..

e.g. DiSEqC 1 for 19.2E DiSEqC 2 for 13.0E and so on
i ordered my satellites.xml in the same way, 1st 19.2 second 13.0 ...

u may give it a try

or just convert your E2 settings

Sounds interesting. But it's strange that the order must be the same of the diseqc.

Das mit der satellites.xml werde ich auch mal versuchen....
Ich verwende eigentlich immer die von http://satellites-xml.eu , und da steht auch Hotbird 13,0 vor Astra 19,2, was nicht meiner DiseqC- Anordnung entspricht.

Die nehme ich im Grunde auch fast, denn das Update via Extras Menü holt die von einem Server der die als Grundlage verwendet.

Fakt ist aber, daß das ein stm24-Problem ist, und das erst ab rev37...!