Timeraufnahme

amaroy1 · #1

Hallo
ich habe mir das NMP auf meine UFS913 geladen. Hat auch alles geklappt. Nun habe ich ein Problem Timeraufnahme. Die Box starten nur, wenn sie im "standby" steht. Im "deep standby" bleibt sie aus. Kann ich das ändern?
Danke

#2

Ist leider derzeit noch ein Bug mit dem Timer im DeepStandby.

#3

Wird da in naher Zukunft ein Fix erwartet?

BPanther-Mobil · #4

Kann ich noch nicht sagen, kommt drauf an, wer das Problem verursacht.

#5

??? Geht doch....

amaroy1 · #6

Es gibt eine neue Version.
Wie führe ich das Update durch?
Danke

BPanther-Mobil · #7

Seit wann gehts denn wieder? Gab doch immer wieder Probleme mit.

#8

Mmmhhh....
hatte noch nie Probleme mit nacktem GIT.
Also eine Kurzaufnahme von 7 Minuten programmiert und Box in den Deep geschaltet.

# Box geht in Deep und setzt die WakeUp ( ist zwar 2 Stunden Differenz, aber egal ).....

Code: Alles auswählen

waiting on current time from fp ...
success reading time from fp
Current Fp Time:     15:44:09 12-05-2013 (UTC)
Current Linux Time:  15:44:10 12-05-2013 (UTC)
Setting Current Fp Time to = FFFFFFDC68 15 44 10 (mtime)
Getting enigma2 wakeup time - Done
Getting neutrino wakeup timeopening /var/tuxbox/config/timerd.conf
 - Done
checkConfig
configs: DISPLAY = 4309088, DISPLAYCUSTOM = 4309088, CUSTOM =     %H:%M:%S    
, WAKEUPDECREMENT  300
Planned Wakeup Time: 15:47:00 12-05-2013 (UTC)
Setting Planned Fp Wakeup Time to = FFFFFFDC68 15 47 0 (mtime)
Entering DeepStandby. ... good bye ...

INIT: no more processes left in this runlevel

# Box wacht 5 Minuten vor der Aufnahme auf....

Code: Alles auswählen

Board: STx7105-PDK  [32-bit mode]
Timeout

boot_mode = 0


U-Boot 1.3.1-g86e3c4c1-dirty (Oct 31 2011 - 12:29:23) - stm24_0050

Hit any key to stop autoboot: 10  9  8  7  6  5  4  3  2  1  0 
(Re)start USB...
USB:   scanning bus for devices... 2 USB Device(s) found
       scanning bus for storage devices... 1 Storage Device(s) found

# Geht zum last Channel: WDR HD Dortmund.............

Code: Alles auswählen

[LT:007497a0:demux ] _open #0: source (0) did not change
[LT:0074d380:demux ] _open #0: source (0) did not change
[LT:00749718:demux ] _open #0: source (0) did not change
[zapit] sending capmt....
[femanager.cpp:getIndependentFE:476] Check fe0: locked 0 freq 12421000 TP 308500c004b10001 - channel freq 12421 TP 308500c004b10001 has sat 192: yes
[femanager.cpp:getIndependentFE:488] Selected fe: 0
[LT:00000000:demux ] SetSource(1, 0) => 0 to 0
[capmt.cpp:SetMode:260] channel c2d404b100016ea7 [WDR HD Dortmund] mode 0 START src 0 mask 0 -> 1 update 0
[pmt] set update filter, sid 0x6ea7 pid 0x1590 version 6
[LT:00875838:demux ] _open #0: source (0) did not change
17:48:12.607 [sectionsd] Reading Information finished after 28670 miliseconds (14572 events)
17:48:22.634 eitThread cache 50 complete: 3589
17:48:22.653 eitThread: skipping to next filter 1 from 4 (timeouts -2)
[LT:008699d0:demux ] _open #0: source (0) did not change
17:48:31.033 eitThread cache 4f complete: 248
17:48:31.035 eitThread: skipping to next filter 2 from 4 (timeouts -2)
[LT:008699d0:demux ] _open #0: source (0) did not change
/bin/fp_control: SW Version 1.04
Model: ufs913
vBoxType: 10
Selected Model: Kathrein UFS912 frontpanel control utility
init
checkConfig
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM =     %H:%M:%S    
, WAKEUPDECREMENT  300
getTimeFromArg
getTimeFromArg <
Setting Current Fp Time to = FFFFFFDC68 15 48 32 (mtime)
17:48:33.116 eitThread: skipping to next filter 3 from 4 (timeouts 20)
[LT:008699d0:demux ] _open #0: source (0) did not change
17:48:35.195 eitThread: skipping to next filter 4 from 4 (timeouts 20)
17:48:35.195 eitThread: going to sleep 3600 seconds, running 1 scanning 1 blacklisted 0 events 3428
[ConfigFile] saving /var/tuxbox/config/timerd.conf
[ConfigFile] saving /var/tuxbox/config/timerd.conf
Record channel_id bae8000600850083 epg: 6008500835cd5, apidmode 0x0

# Startet pünktlich die Aufnahme mit fe1 auf Cinema HD ( Live TV WDR HD bleibt aufm Bildschirm )

Code: Alles auswählen

[neutrino.cpp] executing /var/tuxbox/config/recording.start.
setPauseScanning true
17:52:00.318 Request of stop scanning (now scanning).
CutBackNeutrino channel_id bae8000600850083 mode 1
[frontend.cpp:Lock:288] [fe0] usecount 1 tp 308500c004b10001
[femanager.cpp:getIndependentFE:476] Check fe0: locked 1 freq 12421000 TP 308500c004b10001 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:476] Check fe1: locked 0 freq 0 TP 0 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:488] Selected fe: 1
[LT:00000000:demux ] SetSource(2, 1) => 0 to 1
ZapForRecord: Sky Cinema HD (bae8000600850083)
[femanager.cpp:getIndependentFE:476] Check fe0: locked 1 freq 12421000 TP 308500c004b10001 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:476] Check fe1: locked 0 freq 0 TP 0 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:488] Selected fe: 1
[LT:00000000:demux ] SetSource(2, 1) => 1 to 1
[fe1] sat pos 192 -> 192 motor pos 0 -> 0 usals off
[fe1] tone on
[fe1] FE_SET_TONE took: 4 msec (min 2 max 4)
[fe1] voltage 18
[fe1] tune to 11914000 DVB-S2 QPSK 9/10 H/L srate 27500000 (tuner 1314000 offset 10600000 timeout 4000)
[frontend.cpp:getEvent:530] [fe0,1] ******** max timeout: 4000

[fe1] poll has event after: 0 msec (min 0 max 273)
[fe1] poll has event after: 276 msec (min 0 max 276)
[frontend.cpp:getEvent:565] [fe0,1] ******** FE_HAS_LOCK: freq 1314000
[fe1] tuning took: 276 msec (min 273 max 276)
[LT:00a431d0:demux ] _open: setting /dev/dvb/adapter0/demux1 to source 1
[zapit] parsing pmt pid 0x64 (Sky Cinema HD)
CutBackNeutrino found same tp, zapTo_record channel_id bae8000600850083 result 1
[frontend.cpp:Unlock:295] [fe0] usecount 0 tp 308500c004b10001
CutBackNeutrino channel_id bae8000600850083 mode 1 : result OK
Record: channel bae8000600850083 recording_id 1
[zapit] recording mode: 1
fsk:16, Genre:16, Dauer: 110

Start: file /hdd/movie/Sky_Cinema_HD_Die_Bourne_VerschwÃ¶rung20130512_175204.ts vpid 4ff apid 0
[LT:34d23848:record] cRecord 2
[LT:34d23848:record] Open
[LT:34d23848:record] Start: fd 34, vpid 0x4ff
[LT:34dde680:demux ] _open #2: source (1) did not change
[LT:34dde680:demux ] _open #2: source (1) did not change
[frontend.cpp:Lock:288] [fe1] usecount 1 tp 2e8a00c000060085
[LT:34d23848:record] RecordThread: begin
[LT:34d23848:record] BUFSIZE=0x400000 READSIZE=0x40000
[femanager.cpp:getIndependentFE:476] Check fe0: locked 0 freq 12421000 TP 308500c004b10001 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:476] Check fe1: locked 1 freq 11914000 TP 2e8a00c000060085 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:488] Selected fe: 1
[LT:00000000:demux ] SetSource(2, 1) => 1 to 1
[capmt.cpp:SetMode:260] channel bae8000600850083 [Sky Cinema HD] mode 1 START src 1 mask 0 -> 2 update 0
NeutrinoMessages::EVT_RECORDMODE: on
[neutrino] StopSubtitles
showChannelLogo: logo_available: 1 file: /logos/4b100016ea7.jpg
getImage: resize  /logos/4b100016ea7.jpg to 71 x 43 
after showchannellogo, mode = 3 ret = 3 logo_ok = 1
StartSubtitles: Show
[dvb-sub] ***************************************** start, stopped 1 pid 0
TuxTxt subtitle unpause, running 0 pid 0 page 0
[ConfigFile] saving /var/tuxbox/config/timerd.conf
NeutrinoMessages::RECORD_STOP: eventID 1 channel_id bae8000600850083
Stop: eventID 1 channel_id bae8000600850083
MOVIE INFO: apid 1283 type 1 name Deutsch (AC3) selected 1
MOVIE INFO: apid 1284 type 1 name Englisch (AC3) selected 0
Stop: channel bae8000600850083 recording_id 1
[LT:34d23848:record] Stop
[LT:34d23848:record] RecordThread: end
[LT:34dde680:demux ] Close dmx_tp_count < 0!!
[frontend.cpp:Unlock:295] [fe1] usecount 0 tp 2e8a00c000060085
[femanager.cpp:getIndependentFE:476] Check fe0: locked 0 freq 12421000 TP 308500c004b10001 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:476] Check fe1: locked 0 freq 11914000 TP 2e8a00c000060085 - channel freq 11914 TP 2e8a00c000060085 has sat 192: yes
[femanager.cpp:getIndependentFE:488] Selected fe: 1
[LT:00000000:demux ] SetSource(2, 1) => 1 to 1
[capmt.cpp:SetMode:260] channel bae8000600850083 [Sky Cinema HD] mode 1 STOP src 1 mask 2 -> 0 update 0
[LT:34d23848:record] ~cRecord: calling ::Stop()
[LT:34d23848:record] Stop
[LT:34d23848:record] Stop: status not RUNNING? (1)
[LT:34d23848:record] Stop: dmx == NULL?
[LT:34d23848:record] Stop: file_fd not open??
[LT:34d23848:record] ~cRecord: end
StartNextRecording: pending count 0
[neutrino.cpp] executing /var/tuxbox/config/recording.end.
[zapit] recording mode: 0
setPauseScanning false
17:59:00.253 Request of continue scanning (now idle).
[LT:00754470:demux ] _open #0: source (0) did not change
[LT:00754470:demux ] _open #0: source (0) did not change
[LT:00869a58:demux ] _open #0: source (0) did not change

# Aufnahme pünktlich gestoppt und ist auch OK.
Was noch nicht geht ist das wieder schlafen gehen, wenn aus Deep gestartet wurde.

BPanther's Neutrino Forum

Timeraufnahme

Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme

Re: Timeraufnahme