ja, bleibt immer auf "off", egal ob Lüfter an oder aus.
Hier der Serial Log (Bootvorgang, ohne Lüftermodifikation, also Neutrino-Originalzustand)
Code: Alles auswählen
Rebooting... /bin/fp_control: SW Version 1.04
Model: cuberevo
vBoxType: 8
Selected Model: CUBEREVO frontpanel control utility
init
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
U-Boot 1.3.1 (Aug 10 2010 - 16:31:50) - stm23-2008-03-19
Board: cuberevo (0x2D42C041)
Board: 13 grid vfd front
DRAM: 128 MB
Flash: 32 MB
In: serial
Out: serial
Err: serial
Reserve 0x2010000 bytes from 0xa5ff0000 for DGS upgrade buffer.
Setup mac address.
booting...
Reset IDE: Bus 0: OK
Device 0: Model: SAMSUNG HD204UI Firm: 1AQ10001 Ser#: xxxxxxxxxxxxxx
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
1907377 bytes read
## Booting image at a5ff0000 ...
Image Name: Linux-2.6.32.71_stm24_0217
Image Type: SuperH Linux Kernel Image (gzip compressed)
Data Size: 1907313 Bytes = 1.8 MB
Load Address: 84001000
Entry Point: 84002000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Warning: Unable to determine if kernel is built for 29- or 32-bit mode!
Starting kernel console=ttyAS1,115200 panic=3 root=/dev/sda3 rw rootdelay=10 init=/bin/devinit ip=192.168.1.5:192.168.1.6:192.168.1.1:255.255.255.0 mem=128m coprocessor_mem=4m@0x10000000,4m@0x10400000 - 0x00000000 - 0 ...
INIT: version 2.96 booting
INIT: Entering runlevel: 3
192.168.1.5 login: BPanther-Image rev18332-ddt
[mountvirtfs] Mount /dev in tmpfs
[mountvirtfs] Copying device nodes to /dev
/etc/mdev/mdev-mount.sh: line 91: logger: not found
/etc/mdev/mdev-mount.sh: line 99: logger: not found
/etc/mdev/mdev-mount.sh: line 99: logger: not found
/etc/mdev/mdev-mount.sh: line 99: logger: not found
[mountall] Mounting local filesystems...
Cleaning /tmp.
Hostname: cuberevo.
Deconfiguring network interfaces... ifdown: interface lo not configured
ifdown: interface eth0 not configured
done.
Setting up IP spoofing protection: rp_filter.
Configuring network interfaces... done.
Starting portmap daemon....
4096+0 records in
4096+0 records out
4194304 bytes (4.0MB) copied, 0.076352 seconds, 52.4MB/s
copLoadFile (file /lib/firmware/video.elf)
ustslave: Kernel Version: 24
base_address 0x10000000
seeking to 0
seeking to 4e020
seeking to f8378
seeking to f83b0
seeking to f83e8
seeking to 10ce98
seeking to 10cea4
seeking to 10ceb0
seeking to 12ed90
seeking to 12cd74
seeking to 12ee00
4096+0 records in
4096+0 records out
4194304 bytes (4.0MB) copied, 0.075255 seconds, 53.2MB/s
copLoadFile (file /lib/firmware/audio.elf)
ustslave: Kernel Version: 24
base_address 0x10400000
seeking to 0
seeking to 5f00
seeking to 12320
seeking to 1aa20
seeking to 173100
seeking to 173138
seeking to 173170
seeking to 1b9058
seeking to 1b9060
seeking to 1b9068
seeking to 1b9070
seeking to 1d0920
seeking to 1d0a00
rdate: timeout connecting to time server
Thu Jan 16 04:34:00 CET 2020
showSinglePic /var/boot/bootlogo.mvi
VIDEO_SELECT_SOURCE MEMORY (Success)
VIDEO_PLAY (Success)
VIDEO_CONTINUE: (Success)
VIDEO_CLEAR_BUFFER: (Invalid argument)
swapoff: /dev/ramzswap0: No such file or directory
rmmod: can't unload module 'ramzswap': No such file or directory
Model: 'cuberevo'
vBoxType: 8
Input device name: "TDT RC event driver"
Selected Remote: Cuberevo RemoteControl
RemoteControl Map:
KEY_F1 - 00 - 59
KEY_F2 - 01 - 60
KEY_F3 - 02 - 61
INFO - 03 - 358
RADIO - 04 - 385
PREVIOUS - 05 - 412
EPG - 06 - 365
RECORD - 07 - 167
FAVORITES - 08 - 364
MEDIA - 09 - 226
STANDBY - 0A - 116
KEY_F5 - 0B - 63
MUTE - 0C - 113
ARCHIVE - 0D - 361
0BUTTON - 10 - 11
1BUTTON - 11 - 2
2BUTTON - 12 - 3
3BUTTON - 13 - 4
4BUTTON - 14 - 5
5BUTTON - 15 - 6
6BUTTON - 16 - 7
7BUTTON - 17 - 8
8BUTTON - 18 - 9
9BUTTON - 19 - 10
UP - 1A - 103
DOWN - 1B - 108
RIGHT - 1C - 106
LEFT - 1D - 105
REWIND - 1E - 168
OK - 1F - 352
PLAY - 20 - 207
FASTFORWARD - 21 - 208
STOP - 22 - 128
SLOW - 23 - 409
AGAIN - 24 - 129
PAUSE - 25 - 119
MENU - 26 - 139
EXIT - 27 - 102
KEY_F7 - 28 - 65
KEY_BOOMARKS - 29 - 156
RED - 2A - 398
BLUE - 2B - 401
KEY_F8 - 2C - 66
GREEN - 2D - 399
YELLOW - 2E - 400
AUDIO - 2F - 392
SUBTITLE - 30 - 370
TEXT - 31 - 388
CHANNELUP - 32 - 402
CHANNELDOWN - 33 - 403
VOLUMEUP - 34 - 115
VOLUMEDOWN - 35 - 114
WWW - 36 - 150
Supports Long KeyPress: 1
processComplex >
period 140, delay 10
micom version = 1
Using period=140 delay=10
[SEM] DOWN
/bin/fp_control: SW Version 1.04
Model: cuberevo
vBoxType: 8
Selected Model: CUBEREVO frontpanel control utility
init
configs: DISPLAY = 1, DISPLAYCUSTOM = 1, CUSTOM = %H:%M:%S
, WAKEUPDECREMENT 300
[ca_ci] -> GetInstance
[ca_ci] -> cCA 0
>>> Neutrino (compiled Jan 16 2020 04:34:31) <<<
libstb-hal debug options can be set by exporting HAL_DEBUG.
The following values (or bitwise OR combinations) are valid:
component: audio 0x01
component: video 0x02
component: demux 0x04
component: play 0x08
component: power 0x10
component: init 0x20
component: ca 0x40
component: record 0x80
all components: 0xff
[HAL:00000000:init ] hal_api_init begin, initialized=0, debug=0x00
[HAL:00000000:init ] hal_api_init end
[neutrino] frameBuffer Instance created
12288k video mem
CFrameBuffer::setMode avail: 12582912 active: 1
FB: 1280x720x32 line length 5120.
[neutrino] executing /var/tuxbox/config/neutrino.start.
/var/tuxbox/config/neutrino.start failed: No such file or directory
[neutrino] set debuglevel: 0
[HAL:00000000:init ] hal_api_init begin, initialized=1, debug=0x00
[HAL:00000000:init ] hal_api_init end
[neutrino] recording dir: /hdd/movie
[neutrino] timeshift dir: /hdd/movie/.timeshift
[HAL:007c6ac8:power ] SetCpuFreq(0) => set standby = false
[timerd] wakeup from standby: no
[neutrino.cpp] executing /var/tuxbox/config/deepstandby.off.
[neutrino CEC Settings] setCECSettings init CEC settings...
[neutrino] [CNeutrinoFonts] [SetupNeutrinoFonts - 169] font file: /usr/share/fonts/neutrino.ttf
[neutrino] [CNeutrinoFonts] [SetupNeutrinoFonts - 191] standard font family: Arial Narrow
[neutrino] [CNeutrinoFonts] [SetupDynamicFonts - 151] dynamic font family: Arial Narrow
CVFD::setlcdparameter dimm 5 power 1
CVFD::showServicename:
CVFD::ShowScrollText: [Tuxbox-Neutrino 3.7.7 wird gestartet ...]
[fe0/0] frontend fd 9 type 0
[frontend.cpp:getFEInfo:390] ioctl(fd, FE_GET_PROPERTY, &cmdseq): Operation not permitted
WARNING: can't query delivery systems on frontend 0/0 - falling back to legacy mode
[femanager.cpp:Init:104] add fe 0
[frontend.cpp:Open:302] /dev/dvb/adapter0/frontend1: No such device
[frontend.cpp:Open:302] /dev/dvb/adapter0/frontend2: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter0/frontend3: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter1/frontend0: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter1/frontend1: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter1/frontend2: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter1/frontend3: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter2/frontend0: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter2/frontend1: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter2/frontend2: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter2/frontend3: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter3/frontend0: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter3/frontend1: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter3/frontend2: No such file or directory
[frontend.cpp:Open:302] /dev/dvb/adapter3/frontend3: No such file or directory
[femanager.cpp:Init:120] found 1 frontends, 4 demuxes
[zapit] Loading services, channel size 248 ..
[getservices.cpp:LoadServices:951] Loading satellites...
[getservices.cpp:FindTransponder:601] going to parse dvb-s provider 19.2E Ku-band Astra 1KR/1L/1M/1N
[zapit] 1407 services loaded (1407)...
[zapit] service loading took: 650 msec
[getservices.cpp:FindTransponder:601] going to parse dvb-s provider 19.2E Ku-band Astra 1KR/1L/1M/1N
[zapit.cpp:PrepareChannels:1072] LoadServices: success
[bouquets.cpp:parseBouquetsXml:417] reading bouquets from /var/tuxbox/config/zapit/bouquets.xml
[bouquets.cpp:parseBouquetsXml:519] total: 54 bouquets
[bouquets.cpp:loadWebchannels:892] Loading webtv from /var/tuxbox/config/webtv_usr.xml ...
[bouquets.cpp:loadWebchannels:892] Loading webradio from /var/tuxbox/config/webradio_usr.xml ...
[bouquets.cpp:parseBouquetsXml:417] reading bouquets from /var/tuxbox/config/zapit/ubouquets.xml
[bouquets.cpp:parseBouquetsXml:519] total: 73 bouquets
############## CBouquetManager::makeRemainingChannelsBouquet: numbers start at: tv 1 radio 1 ############
[zapit] bouquet loading took: 1378 msec
CServiceManager::SaveServices: total channels: 1418
CServiceManager::SaveServices: processed channels: 1407
[zapit.cpp:Start:2542] channels have been loaded succesfully
[zapit.cpp] diseqc type = 0
[femanager.cpp:loadSettings:248] load config for fe0
[femanager.cpp:linkFrontends:428] linking..
[femanager.cpp:linkFrontends:470] Frontend #0: is master, with loop: no, with rotor: no
[frontend.cpp:setDiseqcType:1813] fe0: NO_DISEQC
[femanager.cpp:linkFrontends:496] pip demux: 2
[ca_ci] -> SetInitMask param:3
[ca_ci] -> SetTSClock to: high
[ca_ci] -> Start
[zapit] GetConfig...
[zapit] starting... tid 1032
[neutrino VideoSettings] setupVideoSystem setup videosystem...
[neutrino VideoSettings] setVideoSettings init video settings...
[rcinput:checkdev] /dev/input mtime changed
[rcinput:open] open /dev/input/js1 failed: No such device
[rcinput:open] open /dev/input/mouse1 failed: No such device
[rcinput:open] opened /dev/input/event0 (fd 23) ev 0x100003
[rcinput:open] open /dev/input/mouse3 failed: No such device
[zapit] sdt monitor started
[rcinput:open] open /dev/input/event2 failed: No such device
[rcinput:open] open /dev/input/mouse2 failed: No such device
[rcinput:open] open /dev/input/mouse0 failed: No such device
[rcinput:open] open /dev/input/event3 failed: No such device
[rcinput:open] open /dev/input/js0 failed: No such device
[rcinput:open] open /dev/input/js2 failed: No such device
[rcinput:open] open /dev/input/mice failed: No such device
[rcinput:open] open /dev/input/js3 failed: No such device
[rcinput:open] open /dev/input/event1 failed: No such device
[zapit.cpp:leaveStandby:2377] standby 1 recording 0
[zapit.cpp:ZapIt:520] [zapit] zap to rbb Berlin (bdf4043100016e2e tp 2f4d00c004310001)
[zapit] GetConfig...
[zapit.cpp:StopPlayBack:2300] standby 0 playing 0 forced 0 send_pmt 1
[fe0/0] tune to 12109000 DVB QPSK 3/4 H/L srate 27500000 pli 0 plc 1 plm 0 (tuner 1509000 offset 10600000 timeout 4000)
[frontend.cpp:getEvent:921] [fe0/0] ******** FE_HAS_LOCK: freq 1509000
[fe0/0] tuning took: 1725 msec (min 1725 max 1725)
[HAL:00838070:demux ] _open: setting /dev/dvb/adapter0/demux0 to source 0
[HAL:00838070:demux ] Read read: Connection timed out fd:24, ev:0x0 DMX_PSI pid:0x0000 flt:0x00
[pat.cpp] dmx read failed
[pat] sid 6e2e not found
[zapit] pat parsing failed
[zapit] ZapIt:2 SCR retry tuning 1 after 266ms
[fe0/0] tune to 12109000 DVB QPSK 3/4 H/L srate 27500000 pli 0 plc 1 plm 0 (tuner 1509000 offset 10600000 timeout 4000)
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] ############################## poll timeout, time: 4004 msec (min 2000 max 4004)
[neutrino] g_info.has_fan: 1
FAN Speed 4
Cannot open /proc/stb/fan/fan_ctrl: No such file or directory
CStreamManager::Listen: on 31339, fd 17
timerd startup, tid 1052
[HAL:0083eec0:demux ] Stop #0: not open!
2020-01-16 04:34:28.568 [sectionsd] start
2020-01-16 04:34:28.574 [sectionsd] Caching: 3 days, 3 hours Extended Text, max 20000 events, Events are old 3 hours after end time
[yhttpd] Webserver nhttpd/3.4.1 (yhttpd_core/1.3.2) tid 1056
2020-01-16 04:34:28.574 [sectionsd] NTP: disabled, command /usr/sbin/ntpd -n -q -p time.fu-berlin.de
Starting STREAM thread keeper, tid 1057
2020-01-16 04:34:28.591 [sectionsd] starting
2020-01-16 04:34:28.591 [sectionsd] SIevent size: 88
2020-01-16 04:34:28.591 [sectionsd] ====> USING SLOW ADDEVENT. export 'NO_SLOW_ADDEVENT=1' to avoid <===
2020-01-16 04:34:28.677 [sectionsd] timeThread::run:: starting, pid 1008 (855639160)
2020-01-16 04:34:28.694 [sectionsd] timeThread: get DVB time ch 0x000000000000 (isOpen 1)
2020-01-16 04:34:28.700 [sectionsd] eitThread::run:: starting, pid 1008 (864027768)
2020-01-16 04:34:28.716 [sectionsd] cnThread::run:: starting, pid 1008 (872416376)
2020-01-16 04:34:28.730 [sectionsd] freeSatThread::run:: starting, pid 1008 (880804984)
[yhttpd] Webserver starting...
[neutrino] menue setup
[neutrino] init menus...
[neutrino] mediaplayer menu instance created
[ca_ci] -> GetNumberCISlots
[ca_ci] -> GetNumberSmartCardSlots
[network config] Instance created
[neutrino] [CNetworkSetup] [getInstance - 89], Instance created
[neutrino] ScanSetup Instance created
[HAL:2ce40208:play ] cPlayback
[mb]->refreshBrowserList
[mb]->refreshFilterList 20
[neutrino CMoviePlayerGui] Instance created...
[neutrino] registering as event client
[neutrino] had to wait 0 ms for timerd start...
[neutrino] Creating channels lists...
[neutrino] got 1245 TV and 171 RADIO channels
[neutrino] all channels took: 4 msec
[neutrino] created 19.2E Ku-band Astra 1KR/1L/1M/1N (192) bouquet with 1245 TV and 160 RADIO channels
[neutrino] sat took: 45 msec
[neutrino] got 11 WebRadio channels
[neutrino] got 67 new TV channels
[neutrino] got 69 removed TV channels
[neutrino] sats took: 87 msec
[neutrino] got 56 TV and 24 RADIO bouquets
[neutrino] took: 99 msec
CNeutrinoApp::SetChannelMode 0 [tv]
[neutrino.cpp:SetChannelMode:2164] newmode 0 sort old -1 new 0
[neutrino.cpp:tvMode:4660] rezap 1 current mode 1
CVFD::showServicename:
CRemoteControl::tvMode
CNeutrinoApp::SetChannelMode 0 [tv]
[neutrino.cpp:SetChannelMode:2164] newmode 0 sort old -1 new 0
**************************** CChannelList::zapTo_ChannelID bdf4043100016e2e
**************************** CChannelList::zapToChannel me 0x8c3bd8 Alle Kanäle tuned 268435455 new rbb Berlin -> bdf4043100016e2e
2020-01-16 04:34:30.027 [sectionsd] commandserviceStopped
2020-01-16 04:34:30.027 [sectionsd] cnThread: stop eit update filter (not active)
2020-01-16 04:34:30.028 [sectionsd] commandserviceStopped done
stopPlayBack: stopping...
stopPlayBack: stopped
CChannelList::adjustToChannelID me 0x8c3bd8 [Alle Kanäle] list size 1245 channel_id bdf4043100016e2e
[zapit.cpp:ZapIt:520] [zapit] zap to rbb Berlin (bdf4043100016e2e tp 2f4d00c004310001)
[zapit] saving channel, apid 0 sub pid 0 mode 0 volume 24
[zapit] GetConfig...
[zapit.cpp:StopPlayBack:2300] standby 0 playing 0 forced 0 send_pmt 1
2020-01-16 04:34:30.051 [sectionsd] commandserviceChanged: Service change to bdf4043100016e2e demux #0
2020-01-16 04:34:30.051 [sectionsd] changeDMX: for 0x4e not ignored! even though real_pauseCounter> 0 (1)
2020-01-16 04:34:30.052 [sectionsd] changeDMX: for 0x50 not ignored! even though real_pauseCounter> 0 (1)
2020-01-16 04:34:30.052 [sectionsd] changeDMX: for 0x60 not ignored! even though real_pauseCounter> 0 (1)
CHDDDestExec: checking /sys/block/sda
[ca_ci] -> Ready param:1
################################## after all ##################################: 18580 msec
[neutrino] initialized everything
[CPlugins] could not find startup
CRemoteControl::handleMsg: EVT_TUNE_COMPLETE (bdf4043100016e2e)
[fe0/0] tune to 12109000 DVB QPSK 3/4 H/L srate 27500000 pli 0 plc 1 plm 0 (tuner 1509000 offset 10600000 timeout 4000)
[HAL:00849c80:demux ] Read:1 ========== fd has changed, 32->-1 ==========
2020-01-16 04:34:31.711 [sectionsd] timeThread: get DVB time ch 0x043100016e2e rc: -1 neutrino_sets_time 0
2020-01-16 04:34:31.712 [sectionsd] timeThread: Time set FAILED (enabled: ntp 0 dvb 1)
2020-01-16 04:34:31.739 [sectionsd] commandserviceChanged: Service change to bdf4043100016e2e demux #0
[fe0/0] FE_HAS_SIGNAL
CRemoteControl::handleMsg: EVT_TUNE_COMPLETE (0000000000000000)
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
2020-01-16 04:34:32.719 [sectionsd] timeThread: get DVB time ch 0x043100016e2e (isOpen 1)
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] ############################## poll timeout, time: 4004 msec (min 2000 max 4004)
[zapit] ZapIt:1 SCR retry tuning 1 after 702ms
[fe0/0] tune to 12109000 DVB QPSK 3/4 H/L srate 27500000 pli 0 plc 1 plm 0 (tuner 1509000 offset 10600000 timeout 4000)
[fe0/0] FE_HAS_SIGNAL
[dvb-sub] start, stopped 1 pid 0
[HAL:0083eec0:demux ] Stop #0: not open!
[dvb-sub] started with pid 0xffffffff
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_SIGNAL
[fe0/0] FE_HAS_CARRIER
[fe0/0] FE_HAS_SIGNAL
[fe0/0] ############################## poll timeout, time: 4004 msec (min 2000 max 4004)
CRemoteControl::handleMsg: EVT_TUNE_COMPLETE (0000000000000000)
CVFD::showServicename: (rbb Berlin)
zap failed!
Problem scheint an dieser Stelle zu liegen:
[neutrino] g_info.has_fan: 1
FAN Speed 4
Cannot open /proc/stb/fan/fan_ctrl: No such file or directory